kleiner tgb 11 links
| C303 HOME Deutsch | C303 HOME English |
kleiner tgb 11 rechts

News: Forums-Migration in Planung, siehe Das-Letzte-Wort

Willkommen, Gast. Bitte Login oder Registrieren.

  21.November 2026 17:47:11

Seiten: [1] Antwort Überwachen Senden Sie dieses Thema Drucken
   Autor  
All-Posts
 Thema: TGB 131C Petrol Consumption  (Gelesen 2608 mal)
johnnyk

**

Offline

Einträge: 421



Ich liebe dieses Forum!

Profil anzeigen WWW eMail
TGB 131C Petrol Consumption
« am: 18.August 2013 14:23:47 »
Antwort mit Zitat nach oben
Hello forum members. This is Johnny from Perth Western Australia.
I have imported a 6 wheeler Aluzinc C model and and spent last 5 years restoring my truck part time .
I replaced the B30A motor with a B30E fuel injection from Donor 164E sedan.
The B30E motor has done more than 100000km but has good compression and does not burn oil. However I think the Jetronic fuel injection is running motor a little too rich.

I would like to address this question to members who own TGB 13 hardbody(command truck with B30A or B30E motor).
For 100km of highway driving (speed around 90KPH) how many litres of fuel should I be using?
johnny
Moderator benachrichtigen   Gespeichert
johnnyk

**

Offline

Einträge: 421



Ich liebe dieses Forum!

Profil anzeigen WWW eMail
Re:TGB 131C Petrol Consumption
« am: 19.August 2013 16:16:5 »
Antwort mit Zitat nach oben
Hello Der Harms, Thank you for the  D-jetronic Link. It is very helpful.  Yes I will try and post some pictures of the B30E installation tommorow or next day. I am happy to share information with  forum members. Do you Have C303 or C306(TGB equivalent) ? I Love these trucks, they are very spartan but very practical.  I have the TGB13 command truck.

It very easy to  to install B30E motor into TGB engine bay. When you lift motor in position, you have to tilt motor to avoid catching the big inlet manifold on engine mounts or remove engine mounts first and attach to motor then lift motor into positon. It is good if you have helper to guide the alignment of engine mount bolt holes.  The manifold will Just fit in motor bay.
You can fit K&N air filter that sits under engine cover or I fitted a Donaldson air filter and snorkel. I decided on a snorkel because the inlet air gets very warm if you use a standard filter under engine cover. If you can capture cooler air the engine will give slighly better horsepower. My snorkel is fitted behind passenger seat and is mounted on cabin roof.



johnny
« Letzte Änderung: 24.August 2013 03:12:54 von johnnyk » Moderator benachrichtigen   Gespeichert
johnnyk

**

Offline

Einträge: 421



Ich liebe dieses Forum!

Profil anzeigen WWW eMail
Re:TGB 131C Petrol Consumption
« am: 22.August 2013 05:55:32 »
Antwort mit Zitat nach oben
Thank you Moransisse for you ignition information.  I did look at 123 ignition system but the cost was prohibitive.
I used an alternative Solid state ignition on original distributor. It was from Hot-Spark bought on Ebay USA.  The model was for 6cylinder Volvo 3B06U1 for RH mounted points or 3B06U1L for LH mounted points--I can't remember which it was for me. The cost was about USD60 . I am not sure if they are still available. There is a UK version but it is not compatible with the non Vacuum B30E distributor on my motor.

One more thing I remember now on engine swap --(old age happening-- Hello Altzheimers?)  You need to discard the large 24 Volt dropping resistor that is mounted next to ignition coil on the engine bay fire wall and bypass it.

cheers!!!
 
johnny
« Letzte Änderung: 28.August 2013 13:27:7 von johnnyk » Moderator benachrichtigen   Gespeichert
johnnyk

**

Offline

Einträge: 421



Ich liebe dieses Forum!

Profil anzeigen WWW eMail
Re:TGB 131C Petrol Consumption
« am: 24.August 2013 01:8:12 »
Antwort mit Zitat nach oben
I have also low Km spare B30A motor that I exchanged the carburetor head for a B30E head from 164E car enthusiest. I fitting hardened valve seats, new valve guides and stem seals to run unleaded petrol and will fit to B30A block using 0.8mm head gasket not the standard B30A/F head gasket--when I get some time.
I am not 100% sure but I believe some of the B30A heads have already the Injector ports installed but blocked from factory. You can see the ports by removing the engine cover hatch.

Can some members please verify if this is true?

  cheesy B30E motor installation re-posted in Modification section of Forum.
johnny
« Letzte Änderung: 28.August 2013 13:36:37 von johnnyk » Moderator benachrichtigen   Gespeichert
Seiten: [1] Antwort Überwachen Senden Sie dieses Thema Drucken
Powered by MySQL Michaels-Volvo-Offroader-Forum | © 2001-2004 YaBB SE
forked to php5 & mysql-5 & XHTML in 2009 by mibu
lifted to php8.2 in 2024 by mibu
Powered by PHP

| Datenschutz | Impressum |

Seite erstellt in 0.075 Sekunden. 19 Queries.