kleiner tgb 11 links
| C303 HOME Deutsch | C303 HOME English |
kleiner tgb 11 rechts

News: Board-Migration in progress, look at adminitrators-opinion

Willkommen, Gast. Bitte Login oder Registrieren.

  21.November 2026 20:24:0

Seiten: [1] Antwort Überwachen Senden Sie dieses Thema Drucken
   Autor  
All-Posts
 Thema: Interior heat - Dash control  (Gelesen 3663 mal)
WJM

**

Offline

Einträge: 4931





Profil anzeigen WWW eMail
Interior heat - Dash control
« am: 7.Juni 2008 23:15:8 »
Antwort mit Zitat nach oben
Sorry, hatte es schon auf English verfasst, mal wieder zu faul zum uebersetzen....;))


Some of you might remember the stubborn interior-heat dash controls in my
Volvo....I was pretty sure the cable was broken, since the rotating knob went
from very very heavy to 'no resistance', all at once, many moons ago, and no
force to clamp the knob itself onto the dash either....today, being bored, I
looked a bit more carefully, and noticed that the upper part of the cable,
visible just under the knob, didn't rotate at all....but a matching size screw
driver was all it took to get it going again (still pretty stiff, but at least
I can now switch between 'summer' and 'winter'....:))
Seems the two prongs on the rotating knob just got bend too much towards
eachother, not holding onto the cable in any way (still a bit baffled how it
could change so suddenly).

I know the proper service procedure is to remove & straighten the entire cable,
lubicrate it well, and re-install....but has anyone tried lubricating it just
like it is, from the dash side downwards?
(not quite sure which side is stiff/sluggish, dash-side or valve-side....if I
go by feel, trying to rotate the valve by hand, inside the engine-bay, I would
say the upper/dash side is the culprit)

Any comments, anyone attacked this stubborn beast before, from several angles?

Also any tips or tricks to improve the rotating knob design?....those tiny
steel prongs look way too fragile for their task....but maybe I underestimate
the very easy movement of the cable, in well-lubed/factory condition....:))
I would be tempted to fill the gap between the prongs, with some creative
soldering, so make them stronger....but that would defeat their purpose as
spring-clamps, clamping to the stationary part of the cable tube.

Btw, for those with alu-zinc conversion, and re-location of both choke and
hand-
throttle: they could try fabricating a swing-handle in the upper part of the
dash, with a new type of cable, and control the heat valve that way.
(anyone ever invented another function/application in that position, either
mechanically/cable or electronically?....one could even be tempted to control
the radio-volume that way....:))
(or a heater valve in the rear-passenger circuit, instead of just on/off for
the rear blower)
*Verkaufe Battery-Equalizer/Charge-Balancer/Wandler 24->12v/100A*


Those who wander are not necessarily lost
J.R.R. Tolkien
...and not all who launder are washed/WJ....;))


<w.j.markerink@A1.NL>
Moderator benachrichtigen   Gespeichert
WJM

**

Offline

Einträge: 4931





Profil anzeigen WWW eMail
Re:Interior heat - Dash control
« am: 8.Juni 2008 14:23:13 »
Antwort mit Zitat nach oben
Zitat von: Anthony am 8.Juni 2008 09:4:59
Sorry to here that you have been having one or two niggles.  It can be the small things that can be so frustrating and make things a chore.  Having been brought up with old motor bikes and driving in al weathers one soon learnt the use of a cable oiler.  I have not seen one for years and I think that mine was stolen along while a ago.  In the old days it was a necessity to lubricate or the main controll cables would cease, and or break.  The muscles on the left forearm used to have to overcome the increasing effort.  It was a very useful bit of kit, one only had to unfasten one end I recall, feeding the freed terminus through the oiler and then push what ever through, job done for another few months.  Cables where not as good then and the inner sheath would chafe against the rusting wire.  I suspect that they are much better today.  Perhaps you might be able to replace the cables from a motorcycle dealer.  One used to be able to make them up but perhaps that was in an age gone by, its eons since I last straddled any form of two wheeler.

You mention a hand throttle, I have not discovered one, should I?



Yours is alu-zinc, which means converted carburator-controls; both choke and hand throttle on the tunnel, behind the gear stick (choke left, throttle right, IIRC).

Zitat:
My very first bike was a Ducati MK III and not only did the cables gunge up but also the electrics one used to think that the wires where only their to show.  When I reluctantly went into Japanese bikes I discovered a world of working lights and cables that operated, the latter for quite some time before needing any attention.  I remember at night marvelling at being able to watch the red glow of speedometer and tachometer as the needle raced across.  The idiot lights probably would have been more effective than the dim glow of the Ducati headlamp!  The earlier bikes had insufficient binnacle lighting because it would have been pointless as the needle shimmied and danced their way around the clock occasionaly recording the correct speed or RPM, well at lest twice per dance any way. 

Talking of dancing needles, my speedometer is ticking  and dancing slightly, I guess it need lubricating, its a sure sign that it is on its way out.  The dancing will from memmory become more excited before the dancer dies from exhaustion.



Don't *all* British vehicles have a dancing needle?....:))
IIRC, mine isn't too steady either.

Zitat:
I know the rotary knob that you refer, it controls the heat.  The rear heater I am not so sure about it switches on and of from the console but does it allow one to switch it on and blow cold air.  The last time I tried when we had our first sun, I am sure my wife complained that it was getting hotter in the back when I thought I might be blowing cool air, having turned the rotary know down and enjoying a cool breeze on my legs.



There might be a slight difference between military vehicle with complete/standard configuration, and mine, since I recently saw somebody write that he also had a heating valve in the rear compartment, which mine certainly does not have (but mine was build by Tollarp, and Volvo only supplied cab/frame, so there is no good standard configuration for the rear body....they just mounted whatever components they got).

Zitat:
What is that little thing close to the rear heater, it has wires going to it and a pipe rising out of its top and curved over like a samovar?



That is one thing you might want to get a spare unit for, just in case, since it controls front-drive, being an electrically controlled vacuum valve (you can hear it clunk and hiss every time you turn the ignition switch, or tap the brakes, or select the '4wd' button).
(offroad, it is not a problem when it breaks, since the default setting is 'engaged front wheel drive', regardless whether the failure is vacuum or electric; all this device does is *dis*engaging front wheel drive)

Zitat:
By the way do we all have a remote battery isolation leaver?  I am wondering if I where to pull it when parking in dodgy neighbourhoods would a likely car thief be fooled for very long? rolleyes



I detached mine from the chain, and put a quick-release system inbetween, which is normally used for key-chains (a ring on each side, with a cylinder inbetween, which splits in a male and female part....removal/disconnect by pushing a knob on top of the cylinder).
You need 2 of these units, and attach one set to the ignition key, and one set into the chain.

This way you can still hang the knuckle-key onto the chain during normal driving, filling up at the fuel station, etc....but when leaving/parking, you can take the key with you, by attaching it to the ignition key (and leave the 'idle' half of the quick release on the chain (during driving, you have the 'idle' half on the ignition key).
(on which you probably also have a key for the padlock of the fuel filler cap)

Takes a bit of practising before you get the hang of it, but with some experience it gets pretty foolproof....also, by the sheer weight difference of the knuckle-key, I always know instantly whether I have all keys with me or not.

Which reminds me that I still don't have a spare set of those knuckle-keys....I once tried, bought several stainless steel copies from a German guy....but for some strange reason, they don't fit....impossible to *see* any difference....diameter is equal, depth is equal, cross-pin sits exactly in the same spot, also seem depth....

Anyone ever found an exact & proven match from generic sources, or even another known brand/type of military vehicle?



*Verkaufe Battery-Equalizer/Charge-Balancer/Wandler 24->12v/100A*


Those who wander are not necessarily lost
J.R.R. Tolkien
...and not all who launder are washed/WJ....;))


<w.j.markerink@A1.NL>
Moderator benachrichtigen   Gespeichert
WJM

**

Offline

Einträge: 4931





Profil anzeigen WWW eMail
Re:Interior heat - Dash control
« am: 8.Juni 2008 18:59:59 »
Antwort mit Zitat nach oben
Zitat von: Anthony am 8.Juni 2008 14:51:9
No hand throttle in my cab unless I remove the engine cover and tickle the carbs direct.  grin



Weird; most conversions I have seen had two T-shape pull-handles on the tunnel....maybe yours is one of the very last conversions, when they ran out of parts....;))

Zitat:
Interesting what you may have done to the cut off but I can not quite visualise it.


Overhere, you can find them in the smaller key-shops annex shoe-repair-shops.
On their display, it is just a cylinder with two key rings on each end.
Bought a complete rack of those things, 1-2 euro's each, since I already bought 7 spare knuckle-keys, and had 6 extra ignition- and door-keys made, so I could assemble 7 identical sets of keys, all fitting the system....:))
And on long trips, you want a spare 'detacher' anyway, since the interior ball-release system (almost like the connection between ratchet-wrench and socket) is not entirely dust- & rust-proof (but 15k km's in desert dust, gruelling Chinese humidity and the Russian chemical-polluted atmosphere is still a good score for something so nifty & cheap....:))


*Verkaufe Battery-Equalizer/Charge-Balancer/Wandler 24->12v/100A*


Those who wander are not necessarily lost
J.R.R. Tolkien
...and not all who launder are washed/WJ....;))


<w.j.markerink@A1.NL>
Moderator benachrichtigen   Gespeichert
Seiten: [1] Antwort Überwachen Senden Sie dieses Thema Drucken
Powered by MySQL Michaels-Volvo-Offroader-Forum | © 2001-2004 YaBB SE
forked to php5 & mysql-5 & XHTML in 2009 by mibu
lifted to php8.2 in 2024 by mibu
Powered by PHP

| Datenschutz | Impressum |

Seite erstellt in 0.0738 Sekunden. 19 Queries.