| Michaels-Volvo-Offroader-Forum | VOLVO C30x und Verwandte | C303/C304/C306 + TGB-11/13/20/1111 | « vorheriges Thema folgendes Thema » |
|
||||
Autor
|
Thema: TGB 131C Petrol Consumption (Gelesen 2607 mal) | |||
| ||||
|
Hello forum members. This is Johnny from Perth Western Australia.
I have imported a 6 wheeler Aluzinc C model and and spent last 5 years restoring my truck part time . I replaced the B30A motor with a B30E fuel injection from Donor 164E sedan. The B30E motor has done more than 100000km but has good compression and does not burn oil. However I think the Jetronic fuel injection is running motor a little too rich. I would like to address this question to members who own TGB 13 hardbody(command truck with B30A or B30E motor). For 100km of highway driving (speed around 90KPH) how many litres of fuel should I be using? | ||||
johnny
|
||||
| ||||
|
20l/100km ... If the Engine is in Good condition and well adjusted.
| ||||
|
Rickard SJTRPTGB1314
|
||||
| ||||
|
The most here tell somthing about 22-24 L/100 with the B30A in a 6-weehler and 17-19L/100 in the 4-weehler.
The B30E in a 6-weehl ...I think there is no one with this engine here. Just before one week I bought a B30E with even the same idear Do you got some pictures from the maschine inside of the car? Sorry, only in german, but here you´ll find everything to get your B30E with the D-Jetronik running pretty well! www.aircooled-nation.com/printthread.php?tid=1014 der Harms | ||||
|
||||
| ||||
|
Hello Der Harms, Thank you for the D-jetronic Link. It is very helpful. Yes I will try and post some pictures of the B30E installation tommorow or next day. I am happy to share information with forum members. Do you Have C303 or C306(TGB equivalent) ? I Love these trucks, they are very spartan but very practical. I have the TGB13 command truck.
It very easy to to install B30E motor into TGB engine bay. When you lift motor in position, you have to tilt motor to avoid catching the big inlet manifold on engine mounts or remove engine mounts first and attach to motor then lift motor into positon. It is good if you have helper to guide the alignment of engine mount bolt holes. The manifold will Just fit in motor bay. You can fit K&N air filter that sits under engine cover or I fitted a Donaldson air filter and snorkel. I decided on a snorkel because the inlet air gets very warm if you use a standard filter under engine cover. If you can capture cooler air the engine will give slighly better horsepower. My snorkel is fitted behind passenger seat and is mounted on cabin roof. | ||||
johnny
|
||||
| ||||
|
Yes, to change the Motor isn´t very difficult.
My last change : www.c303.de/c303-forum/index.php?board=36;action=display;threadid=10994 But now for me is the most interesting point the Air-Inlet. The filter must become a new position. I´m already installed an snorkel too, but in Front of the car, baybe you can see on the upper link. The Question is the "air-inlet-tube" ( dont know the english word...) from the Airfilter to the engine. Will it fit in the original position or do you change it? A picture will be very nice! Thanks a lot! And yes, to bild up the head with harded valveseats is a good idear. I drove that way about 30.000 km unleaded and it looks all quite new. | ||||
|
||||
|
markusweiss
Gast |
| |||
|
||||
| ||||
|
try to let off the" http:// " from the file...!
| ||||
|
||||
| ||||
|
G'day Jonny!
Nice engine conversion, the work is looking very professional. Thanks for sharing your experience! One thing might be maybe interesting for you as it seems that you are not afraid haveing ECUs in the car: the 123igintion distributer http://www.123ignition.nl/id/14.html Best Regards, Moranisse | ||||
|
||||
| ||||
|
Thank you Moransisse for you ignition information. I did look at 123 ignition system but the cost was prohibitive.
I used an alternative Solid state ignition on original distributor. It was from Hot-Spark bought on Ebay USA. The model was for 6cylinder Volvo 3B06U1 for RH mounted points or 3B06U1L for LH mounted points--I can't remember which it was for me. The cost was about USD60 . I am not sure if they are still available. There is a UK version but it is not compatible with the non Vacuum B30E distributor on my motor. One more thing I remember now on engine swap --(old age happening-- Hello Altzheimers?) You need to discard the large 24 Volt dropping resistor that is mounted next to ignition coil on the engine bay fire wall and bypass it. cheers!!! | ||||
johnny
|
||||
| ||||
|
I have also low Km spare B30A motor that I exchanged the carburetor head for a B30E head from 164E car enthusiest. I fitting hardened valve seats, new valve guides and stem seals to run unleaded petrol and will fit to B30A block using 0.8mm head gasket not the standard B30A/F head gasket--when I get some time.
I am not 100% sure but I believe some of the B30A heads have already the Injector ports installed but blocked from factory. You can see the ports by removing the engine cover hatch. Can some members please verify if this is true? B30E motor installation re-posted in Modification section of Forum. | ||||
johnny
|
||||
|
||||
| Michaels-Volvo-Offroader-Forum | VOLVO C30x und Verwandte | C303/C304/C306 + TGB-11/13/20/1111 | « vorheriges Thema folgendes Thema » |









Autor








Gespeichert
B30E motor installation re-posted in Modification section of Forum.