| Michaels-Volvo-Offroader-Forum | VOLVO C30x und Verwandte | C303/C304/C306 + TGB-11/13/20/1111 | « vorheriges Thema folgendes Thema » |
|
||||
Autor
|
Thema: TGB13 Achslagerung Hinterachse (Gelesen 6172 mal) | |||
| ||||
|
Hallo Zusammen,
die Lager meiner Hinterachsstreben (Reaction Rod) sind vermutlich ausgeleiert. Wie ich drauf komme ? Die Antriebsflansche von 2. zu 3. Achse stehen nicht parallel. Das ist vermutlich die Ursache für Vibrationen und erhöhrten Kardanwellenverschleiß ? Hat die schon mal jemand gewechselt ? Wo gibts welche ? (Anfrage bei Tatanka läuft schon; Alternativen ? ) Danke Grüße Uli | ||||
|
||||
| ||||
|
Servus Uli!
Wenn ich das Prinzip richtig verstanden habe, können die Achsen durch die Silent-Blöcke der Streben etwas "mitlenken". Bei meinem lenkt die Achse in der Kurve sicher + / 3 cm aus der Mittellage (an der Federauflage) aus. Daher müsste auch die Verschiebung der Achsen normal sein und dürfte keine Probleme an den Kardanwellen erzeugen. Kann man die Buchsen auspressen? Und dann mit handelsüblichen Silentblöcken ersetzen? Liebe Grüße aus Graz! kawahans | ||||
1314 - weil er so schön ist
|
||||
| ||||
|
Hallo Hans,
das Problem scheint mir nicht das Verschieben zu sein. Ich vermute, dass durch die evntl. ausgeleierten Buchsen, die Achse leicht gekippt (ca. 4-5 Grad )ist. Die Buchsen kann man auspressen. Ob es Ersatz gibt kläre ich gerade. Es sei denn, jemand hat schon eine Bezugsquelle. Polyurethanbuchsen wären wohl eine Alternative. Ob die jemand auf Maß fertigt ? Grüße Uli | ||||
|
||||
| ||||
|
die Teile sind schlecht zu bekommen ! Ich hatte die vor einem jahr beim Rio angefragt ,da waren sie im liefer Rückstand. Ich meine Stückpreis war um 70 euro plus steuer . :-P Sind 10 Buchsen glaube ich ??!!
Ich habe mir dann welche im Maschine/Industrie Teilehandel gekauft ( glaube so 12 Euro incl. ) und "etwas " angepasst . war ne sau Arbeit weil das auspressen ohne Presse ist nicht so ganz einfach . Laut Rio müssten die "originalen " vorgespannt werden was aber eigentlich quatsch ist da das Gummi im Verhältnis kaum Drehkräfte / Druckkräfte auf die Achsen ausüben kann . Wünsche viel spass :-( | ||||
|
||||
| ||||
|
Moin...
Wenn mich nicht alles täuscht haben die silentpuchsen einen innen und außenkäfig. Heißt ein innen und außenrohr. Wenn mich nicht alles täuscht , wurden die auch beim volvo Amazon und P1800 verbaut. Aber Vorsicht es gibt auch dort verschiedene.... Grüße küppi | ||||
|
Auseinandergenommen werden darf alles was nicht wegläuft http://www.tape.tv/musikvideos/Republica/Ready-To-Go
|
||||
| ||||
|
Polyurethanbuchsen (ggf. auch Nylon) sollten auf einer Drehbank einfach herzustellen sein.
In Jeep-Höherlegungsbereich schauen, von der Dimension käme mir das sehr ähnlich vor. Im eingebauten Zustand ist eine vernünftige Messung wohl nicht möglich Leider wäre dann der Vorteil der beweglichen Achse (mit Polyurethan) dahin. Liebe Grüße aus Graz! kawahans | ||||
1314 - weil er so schön ist
|
||||
| ||||
|
Nachtrag:
vielleicht kann man hier etwas passendes finden: http://www.stoeffl.at/katalog/pi/gummi-metall-buchsen.html http://gummi-metall-puffer-shop.de/silentbuchsen http://www.fritz-motorsport.de/index.php?cPath=139 Notfalls doppelt moppeln: eine dünne Buchse zum Anpassen eines "fast" passenden Silentblocks einsetzen. Wenn gar nichts anderes geht, müsste man den kompletten Lenker nachbauen, dann kann man sich schon vorher die Bohrungen nach den vorhandenen Blöcken richten. Alles Gute! Hans | ||||
1314 - weil er so schön ist
|
||||
| ||||
|
Hallo Hans,
Danke. Das sieht doch mal ganz gut aus. Und ein Laden fast um die Ecke Grüße Uli | ||||
|
||||
| ||||
|
ich habe leider keine Unterlagen mehr wie Rechnung oder teile nummer . sorry
| ||||
|
||||
| ||||
|
Kein Problem. Trotzdem Danke.
Ersatz auf dem Weg. Gunter hat noch gute Gebrauchte. Grüße Uli | ||||
|
||||
| ||||
|
...heute kamen die neuen Längslenker.
Ich hab die heute mittag gleich eingebaut. Zunächst leider keine Änderung. Achsen standen immer noch unterschiedlich gekippt. D.H. meine Längslenker waren wohl noch ok. Beim Ausbau hab ich aber festgestellt das die Längslenkerbolzen nicht mehr das erforderliche Anzugsmoment hatten. Die gingen z.T. sehr leicht auf. Ich hab dann den Volvo solange vorne, hinten und mitte aufgebockt, bis alles richtig stand. Dann alle Bolzen richtig angezogen und fertig. Jetzt sieht alles gut aus. Hoffe das bleibt so.... D.H. die Längslenker müssen vorgespannt eingebaut werden. Hauptsächlich deshalb damit beide Achsen (insbesondere die Antriebsflansche) parallel stehen. Das tun sie jetzt.... | ||||
|
||||
| ||||
|
Hi ULI-RT
what is the result ? no more vibration . do you run with 2 or 3 leafsprings in the back ? did you make pre-tension on all 6 arms like the manual states.. thanks | ||||
|
||||
| ||||
|
... better, but not good. Still very noisy in the back.
So I checked the wheelbearings. One ist definitely broken. I took it out this morning and will start to replace the bearings next week. I am going to do this on all wheels. For the pre-tension i jacked the car up und tightend all bolts of the axle. I am running with 3 leafsprings (as is original) | ||||
|
||||
| ||||
|
thanks
the repair book from swedish army states .. loosen all bolts push up axle until 10 cm away from frame and then tighten bolts so that the pre-tention is working against leaf spring.. seams to me you did it opposite so that pre-tension "helps" leaf spring ? how did you check the wheelbearing ? i think it is very hard to do with wheel on or off and with and without brakes installed.. | ||||
|
||||
| ||||
|
Hi Jasper,
you are right. I did it the opposite way. Haven´t found the explanation in the repair book. Where did you find it ? Wheelbearings are hard to check. The bearingclearance was ok. But they were running realy bad. Not round...but rough. I took the wheels of an turned the hub without breakdrum. You can feel, if the bearings are ok or not. If you feel a light rumble while turning the hub, bearing is broken. you have to spend a bit power to turn the hub. I think it would be no problem to move on with the old bearings, but its very noisy... that is what I hope | ||||
|
||||
| ||||
|
thanks
if you look in the database on this forum it is in section 7 "frame/suspension" then go to suspension file 2. then page 3 or 76:3.. right on top of picture it states ( load car until spring if flat then thighten.. it is a somewhat poor translation of the swedish manual i have in hard copy.. it states it more precise . "Push op axle until you measure 100mm between axle top and frame bottom then thighten.. the swedish manual states clearly it is related to c304 where the one on this forum seams to cover both c303 and 04 .. | ||||
|
||||
| ||||
|
... may be you have an other version.
In the version here (english) i can´t found it. Would you mind to share it, so I can do it right ? Thanks Uli | ||||
|
||||
| ||||
|
off course but can you read swedish ? it is quite big but i can try to send it by email if you give me your mail adr.. send it to me on PN .. but all it says is this .
lift axle up until 100mm distance and the fasten control arm.. thats it.. i have just in this moment done it on my car as i just installed them without pre-tension before. still need to test drive it. i was talking to RIJO last year to see if he had new bushings and he was a firm believer as well that they should have pre-tension , he believed that it would help the bushing to stay in center and reduce resonance.. on my car i have 3 new drive shafts and just installed 6 new/used control arms but i still have this resonance at 70kmh , i changed the control arms because some of the bushings had come loose in the vulcanising between rubber and inner steel tube so that pre-tension was no longer possible.. | ||||
|
||||
| ||||
|
Liebe Gemeinde,
Ich benötige eure Hilfe. Heute habe ich meinen Longbody hinten so angehoben, dass die Achsen frei in den Seilen hingen und habe in Achsrichtung gezogen und gestossen. https://vimeo.com/user107024683/review/382057660/9ca7cbcf3b Ist es normal, dass die Achs 2-3 cm Siel hat, oder sind die Längslenkerbuchsen ausgeschlagen? Für euere Antworten vielen Dank Gruss Martin | ||||
Gruss Martin
|
||||
| ||||
|
sehe nix, link ist tot
| ||||
Grüße Daniel
|
||||
|
||||
| Michaels-Volvo-Offroader-Forum | VOLVO C30x und Verwandte | C303/C304/C306 + TGB-11/13/20/1111 | « vorheriges Thema folgendes Thema » |









Autor






Gespeichert
