kleiner tgb 11 links
| C303 HOME Deutsch | C303 HOME English |
kleiner tgb 11 rechts

News: Board-Migration in progress, look at adminitrators-opinion

Willkommen, Gast. Bitte Login oder Registrieren.

  21.November 2026 08:54:20

Seiten: [1] Antwort Überwachen Senden Sie dieses Thema Drucken
   Autor  
Autor-Posts
 Thema: Battery hold-down  (Gelesen 2258 mal)
Mo

**

Offline

Einträge: 349



Ich liebe dieses Forum!

Profil anzeigen
Battery hold-down
« am: 15.Februar 2022 14:3:36 »
Antwort mit Zitat nach oben
My C303 arrived without the battery hold down frame attached. Now that I've had a chance to investigate, I understand why. It's too big for the currently installed batteries. With the adjuster fully screwed in I can still fit my finger under the frame.



How would you resolve this? Pack out the frame with wood, or place something under the batteries to raise them?

Maurice
Moderator benachrichtigen   Gespeichert
der Harms

**

Offline

Einträge: 2834



Das ist der Lars... Lars kommt aus Schweden!

Profil anzeigen
Re:Battery hold-down
« am: 15.Februar 2022 14:18:2 »
Antwort mit Zitat nach oben
a wooden plate, fit in the frame ?
Moderator benachrichtigen   Gespeichert
Friese

**

Offline

Einträge: 1817





Profil anzeigen
Re:Battery hold-down
« am: 15.Februar 2022 14:49:29 »
Antwort mit Zitat nach oben
Die richtigen Batterien verwenden in der richtigen Größe?
Moderator benachrichtigen   Gespeichert
WJM

**

Offline

Einträge: 4931





Profil anzeigen WWW eMail
Re:Battery hold-down
« am: 15.Februar 2022 15:43:30 »
Antwort mit Zitat nach oben
Zitat von: Friese am 15.Februar 2022 14:49:29
Die richtigen Batterien verwenden in der richtigen Größe?

Geht bei AGM oft nicht, noch weniger wenn man sich auf eine bestimmte Marke/Typ festgelegt hat, und/oder sich Maximal-Kapazitaeten aussucht.
(oder eben vom Vorbesitzer etwas ueberliefert bekommen hat)

Fuhrpark hier hat mehr mit Holz als ohne....:))
*Verkaufe Battery-Equalizer/Charge-Balancer/Wandler 24->12v/100A*


Those who wander are not necessarily lost
J.R.R. Tolkien
...and not all who launder are washed/WJ....;))


<w.j.markerink@A1.NL>
« Letzte Änderung: 15.Februar 2022 15:46:31 von WJM » Moderator benachrichtigen   Gespeichert
Mo

**

Offline

Einträge: 349



Ich liebe dieses Forum!

Profil anzeigen
Re:Battery hold-down
« am: 15.Februar 2022 19:27:2 »
Antwort mit Zitat nach oben
Zitat von: Friese am 15.Februar 2022 14:49:29
Die richtigen Batterien verwenden in der richtigen Größe?

Yes, of course that would be ideal, but these batteries were supplied with the vehicle and don't yet need to be replaced.

Zitat von: der Harms am 15.Februar 2022 14:18:2
a wooden plate, fit in the frame ?

Yes. Now that I've had time to think about it, a wooden board under the batteries will be simplest and won't interfere with the cables in any way.

Thanks guys

Maurice
Moderator benachrichtigen   Gespeichert
WJM

**

Offline

Einträge: 4931





Profil anzeigen WWW eMail
Re:Battery hold-down
« am: 15.Februar 2022 20:11:14 »
Antwort mit Zitat nach oben
Zitat von: Mo am 15.Februar 2022 19:27:2
Zitat von: Friese am 15.Februar 2022 14:49:29
Die richtigen Batterien verwenden in der richtigen Größe?

Yes, of course that would be ideal, but these batteries were supplied with the vehicle and don't yet need to be replaced.

Zitat von: der Harms am 15.Februar 2022 14:18:2
a wooden plate, fit in the frame ?

Yes. Now that I've had time to think about it, a wooden board under the batteries will be simplest and won't interfere with the cables in any way.

Thanks guys

Maurice

Forgot how the Volvo 24v floor-plate typically looks like, but yours seems to have holding ridges on the sides/corners.
Unless your extra board also matches this stock 'floorplan', *and* comes with it's own ridges, you decrease the holding power of the entire constellation, in a worst-case/crash scenario.
Wood on top is most often the better way, but that depends on the clamp of course.
(single-battery clamps are often 'U' shaped, so, with wood below, the top holding power can also decrease, but that still is much better than loosing the same 'crash-resistance' on the bottom)

Formschluss comes for Kraftschluss....;))
*Verkaufe Battery-Equalizer/Charge-Balancer/Wandler 24->12v/100A*


Those who wander are not necessarily lost
J.R.R. Tolkien
...and not all who launder are washed/WJ....;))


<w.j.markerink@A1.NL>
« Letzte Änderung: 15.Februar 2022 20:12:18 von WJM » Moderator benachrichtigen   Gespeichert
Mo

**

Offline

Einträge: 349



Ich liebe dieses Forum!

Profil anzeigen
Re:Battery hold-down
« am: 15.Februar 2022 21:7:32 »
Antwort mit Zitat nach oben
This image from the service manual shows both the plate and the hold down frame:



My batteries are a similar length and width to the ones in the manual, but a shorter height. I understand your point that placing wood sheets under the batteries negates the locating ridges on the plate. However if I place wood strips at the top, that effectively raises the frame relative to the terminals, and that increases the risk of a catastrophic short circuit.

I honestly don't like this square frame, it's a relic from when batteries weren't sealed. And why does it have quick release catches? I mean you have to undo the terminals with a spanner before you can remove the frame....

A modern frame would be a single east-west bar, bolted down, as far from the terminals as possible. This isn't a particularly good example, but I'm sure you get the idea.



Maybe I should just ask someone to modify the frame, make the minimum height lower.

Maurice
« Letzte Änderung: 15.Februar 2022 21:8:32 von Mo » Moderator benachrichtigen   Gespeichert
WJM

**

Offline

Einträge: 4931





Profil anzeigen WWW eMail
Re:Battery hold-down
« am: 16.Februar 2022 02:44:29 »
Antwort mit Zitat nach oben
That second picture makes me itchy....no holding power (Formschluss), neither top nor bottom, all relying on friction (Kraftschluss).
(note that no matter how you mount that battery tray, there is no safe orientation....if you mount it length-wise, it might look better in a head-on crash, but any side-crash, or even a slow roll-over, causes total misery....that metal bar possibly even becoming the short circuit itself....)

However, what might still be possible in your configuration, is adding metal L-profiles to/on the bottom of the raiser-board, having just enough margin between the original ridges and the battery, on all sides (possibly not at the corners, but those are not crucial).
Only 2x 2mm margin is needed.
(but I'd also take a deep (read strong-armed) L profile, at least 20mm on the bottom, horizontal (vertical side requires much less, 5-10mm would only collect crud when too long/deep))
*Verkaufe Battery-Equalizer/Charge-Balancer/Wandler 24->12v/100A*


Those who wander are not necessarily lost
J.R.R. Tolkien
...and not all who launder are washed/WJ....;))


<w.j.markerink@A1.NL>
Moderator benachrichtigen   Gespeichert
Seiten: [1] Antwort Überwachen Senden Sie dieses Thema Drucken
Powered by MySQL Michaels-Volvo-Offroader-Forum | © 2001-2004 YaBB SE
forked to php5 & mysql-5 & XHTML in 2009 by mibu
lifted to php8.2 in 2024 by mibu
Powered by PHP

| Datenschutz | Impressum |

Seite erstellt in 0.0736 Sekunden. 21 Queries.