kleiner tgb 11 links
| C303 HOME Deutsch | C303 HOME English |
kleiner tgb 11 rechts

News: Board-Migration in progress, look at adminitrators-opinion

Willkommen, Gast. Bitte Login oder Registrieren.

  21.November 2026 05:22:31

Seiten: [1] Antwort Überwachen Senden Sie dieses Thema Drucken
   Autor  
Autor-Posts
 Thema: Installing the motor and transmission  (Gelesen 1338 mal)
PaulB

*

Offline

Einträge: 24



Ich liebe dieses Forum!

Profil anzeigen
Installing the motor and transmission
« am: 1.Mai 2024 18:23:36 »
Antwort mit Zitat nach oben
Hello again!
Firstly, thanks to everyone who has helped with advice and especially to those who have or are sending me some parts.

I should soon have the B30 and gearbox ready to install so please let me know your preferred method - from underneath, from above and how you moved into position. In two parts or full engine and transmission together. Any equipment you found made it easier?

All your experience and advice is very welcome.
Paul (UK).
Moderator benachrichtigen   Gespeichert
WJM

**

Offline

Einträge: 4931





Profil anzeigen WWW eMail
Re:Installing the motor and transmission
« am: 1.Mai 2024 20:32:50 »
Antwort mit Zitat nach oben
Zitat von: PaulB am 1.Mai 2024 18:23:36
Hello again!
Firstly, thanks to everyone who has helped with advice and especially to those who have or are sending me some parts.

I should soon have the B30 and gearbox ready to install so please let me know your preferred method - from underneath, from above and how you moved into position. In two parts or full engine and transmission together. Any equipment you found made it easier?

All your experience and advice is very welcome.
Paul (UK).


The logistics of removal & installment for my C306, overhaul of engine:

- Engine + transmission(s) were immobilized from below, stacked on wooden euro-pallets.
- Forklift was used to pull vehicle up & (roll) over

Repeat in reverse order....;))

One alternative, one that you might have seen/read about already, but more for transmission than engine: pull from above, inside the cabin, by a hoist-contraption traversing the rear doors (supporting the hoist from the vehicle floor is probably more complicated and/or less stable, and at the very least much less manoeuverable).

*Verkaufe Battery-Equalizer/Charge-Balancer/Wandler 24->12v/100A*


Those who wander are not necessarily lost
J.R.R. Tolkien
...and not all who launder are washed/WJ....;))


<w.j.markerink@A1.NL>
« Letzte Änderung: 1.Mai 2024 21:14:54 von WJM » Moderator benachrichtigen   Gespeichert
PaulB

*

Offline

Einträge: 24



Ich liebe dieses Forum!

Profil anzeigen
Re:Installing the motor and transmission
« am: 1.Mai 2024 21:4:45 »
Antwort mit Zitat nach oben
Ok that sounds really simple... except for the bit about the forklift truck...  grin
« Letzte Änderung: 1.Mai 2024 21:5:8 von PaulB » Moderator benachrichtigen   Gespeichert
WJM

**

Offline

Einträge: 4931





Profil anzeigen WWW eMail
Re:Installing the motor and transmission
« am: 1.Mai 2024 21:24:53 »
Antwort mit Zitat nach oben
Zitat von: PaulB am 1.Mai 2024 21:4:45
Ok that sounds really simple... except for the bit about the forklift truck...  grin

Well, the good/synergetic aspect of this is that you can use that same forklift to lift the cratered engine/transmission combo, onto a trailer, off to the overhaul location/shop....:))

As for lifting the vehicle:
- it was only pulled up on the front, not entirely (much more stable that way, especially with a 6x6)

- fabricating a large/tall hoist contraption is no good alternative for a forklift, being that the vehicle doesn't go up lineary, but angled....forcing the hoist to move along, backwards.
(locking the rear tires isn't easy either, as the parking brake is out (literally))

- hence the only valid alternative is linear, like with a genuine garage-style vehicle-lift, 2- or 4-pillar.

*Verkaufe Battery-Equalizer/Charge-Balancer/Wandler 24->12v/100A*


Those who wander are not necessarily lost
J.R.R. Tolkien
...and not all who launder are washed/WJ....;))


<w.j.markerink@A1.NL>
« Letzte Änderung: 1.Mai 2024 21:26:40 von WJM » Moderator benachrichtigen   Gespeichert
Seiten: [1] Antwort Überwachen Senden Sie dieses Thema Drucken
Powered by MySQL Michaels-Volvo-Offroader-Forum | © 2001-2004 YaBB SE
forked to php5 & mysql-5 & XHTML in 2009 by mibu
lifted to php8.2 in 2024 by mibu
Powered by PHP

| Datenschutz | Impressum |

Seite erstellt in 0.0513 Sekunden. 19 Queries.