| Michaels-Volvo-Offroader-Forum | VOLVO C30x und Verwandte | C303/C304/C306 + TGB-11/13/20/1111 | « vorheriges Thema folgendes Thema » |
|
||||
Autor
|
Thema: c303 gerbox (Gelesen 1874 mal) | |||
| ||||
|
Hallo dear off roaders I'm marin and im writing from Croatia.I don't have any of c 303 but in the future i will have. I own several pinzgauers and unimog 404.In my free time i'm trying to make a custom pinz for extreme with more capabilities than original one, wich means two steering axles, engine on back side, self made very fast and strong winchetc....the main problem for me is that pinz doesent have pto unit, so i tought to mount c 303 gearbox with pto on it.in my country doesen't exsist any of c 303 so i can't see how does it look like.maybe you can help me with some photo or link where can I see photos of tgb gearbox and to judge if it's at least visualy possible to mount a tgb gearbox on pinz engine.thank you and greatings from Croatia. ps: photo of my driving park. I would be wery happy that instead of some pinz is standing some c 303.
![]() | ||||
|
||||
| ||||
|
marin Hi,
Have a look at this picture library http://stiletti.wipsl.com/gallery/album36?page=1 which I found while perusing the wonderful Encyclopedia of WJM world of 4x4, 6x6, 8x8 and every thing else. This shows good visuals of the transmission lay out and drive to the rear most axle of Volvo 6x6 TGB. Anthony Wales GB | ||||
|
Grüße Anthony GB
|
||||
| ||||
|
Thank you but I have allredy seen these pictues.from this view looks very big this transmision
| ||||
|
||||
| ||||
|
Hi, Marin,
I haven't seen a Pinz, but I assume that it would be possible to fit Pinz engine to a C3 gearbox. But that is not your problem! The C3-PTO is not on the primary gearbox, but on the secondary reduction gearbox. This secondary gearbox is constructed for an asymetric power shaft, that is the reason why it is so big - and why it is placed in the middle. To fit into a Pinz it has to be much smaller, because the Pinz uses a symmetric propeller shaft, which runs in the central frame tube. Because of that tecnical specifications there is no space in a Pinz for a PTO. The gearbox is very slim and positioned in besides the middle frame tube. At http://www.zuckerfabrik24.de/steyrpuch/Pinzgauer1.htm near the end of the page are two pictures of the main gerabox under a Pinz (correction from here on...) I have read that the secondary gearbox is positioned near the rear diff. That means that the main shaft comming from the main gearbox will transfer the power in the middle frame tube near the rear axle. That position results in less space between the transfer-gearbox and the rear axle for the PTO. Even if the transfer-gearbox had a neutral position or an position to lead the input-shaft through to the back end of the box, there may be no space left to put anything on it. Only a longer shaft running above the rear axle and ending in the rear bumper may be possible, like on a mog, where you an adapt a lot of tools. If you want to have exact dimensions of the gearbox: Here in the forum is a transfer gearbox (Verteilergetriebe) on sale. regards michael | ||||
"oh, for sure, you can do it with a normal streetcar...."
|
||||
|
||||
| Michaels-Volvo-Offroader-Forum | VOLVO C30x und Verwandte | C303/C304/C306 + TGB-11/13/20/1111 | « vorheriges Thema folgendes Thema » |









Autor








Gespeichert


