| Michaels-Volvo-Offroader-Forum | VOLVO C30x und Verwandte | C303/C304/C306 + TGB-11/13/20/1111 | « vorheriges Thema folgendes Thema » |
|
||||
Autor
|
Thema: oil leak (Gelesen 5940 mal) | |||
| ||||
|
Hello everyone,
there is oil leaking out of my front portal box. The leak is probably comming through the drive shaft bearing, as the oil drips out by the rubber dust cover on to the steering knuckle support. Would that be the CR 23451 seal? (upper portal/axletube oil seal) and should I order other parts too (new dust cover etc.) or can I use the old one? I like to be sure I have all the parts before I start because it is my daily driver. thanks in advance greetings.. Joeri | ||||
|
||||
| ||||
|
viele Grüsse Frank http://www.auf-allen-vieren.de
|
||||
| ||||
If I follow the given document I don't understand what you both mean: Down to page 323 is only one sealing ring on the entry of the diff (page 314/315, part 33) and two sealing rings on top and bottom of the steering knuckle (page 322/323, parts 18 amd 25). On the back axle there is something called X-ring which may be a sealing ring (page 304/305, part 19), but not on the front axle. I don't see any sealing ring between the diff and the wheel gear of the front axle. There I see only the flexible rubber cap or dust cover that is holding the oil from the diff inside. May be there are additional thin washers to stabilitze the edges, but on the pictures I can't find a sealing. Is there any? Which part is it? regards michael | ||||
"oh, for sure, you can do it with a normal streetcar...."
|
||||
| ||||
|
I think he means the Cover (Nr 20 / Page 297).
| ||||
|
viele Grüsse Frank http://www.auf-allen-vieren.de
|
||||
| ||||
that is indeed where the oil is dripping from. | ||||
|
||||
| ||||
|
Ok, it is dripping from the rubber cover, as I read on the edge towards the wheel.
Are your shure that the rubber itself is flexible and closed, no hole, no scratch, no perforation by aging etc.? As i mentinoed I am not shure where the oil is comming from at all. Jens and Nick did remove the steering knuckle, and the oil from the diff came out - but that was because the drive shaft was removed. There should be some kind of seal between the diff and the end of the axle, but I can't see it in the part list. If therw would be no seal, allways a lot of oil from the diff would run into the rubber cap, and it would always drip - that is my opinion. Any suggestions? Michael | ||||
"oh, for sure, you can do it with a normal streetcar...."
|
||||
| ||||
Exactly, only I am not losing oil from the dif, only from the portal box. But I don't think this oil can get so high, which is probably the reason why there is no seal on this side. grtz Joeri | ||||
|
||||
| ||||
|
Ok, that helps.
(Don't blame me for my theoretical ideas) If the oil is only from the portal gear, then it will be transportet by the gear itself to the top, just like the oil pump will transport oil between the housing and the teeth of ther gear. Normally the oil will run down into the housing later. But there is one place where the rubber cap will be worn after a long time, that is probably where the drive shaft runs thru the rubber cap into the portal. There the oil may start to drip out. The other retaining rings on the drive shaft are unlikely to be worn. Please: which part is this CR 23451 seal? (upper portal/axletube oil seal). I can't identify it on the part list. comments welcome michael | ||||
"oh, for sure, you can do it with a normal streetcar...."
|
||||
| ||||
|
[quote author=michael
Please: which part is this CR 23451 seal? (upper portal/axletube oil seal). I can't identify it on the part list.
I got it from Richards site, along with other usefull info. http://www.volvoc303.co.uk/mechanical_info.htm Your theory sounds reasonable, so I will try to order the dust cover. | ||||
|
||||
| ||||
|
I found 3 pictures from Jens (TGB_11) which may explan a little what I said:
![]() The top end with the drive shaft bore will point towards the differential ![]() The curved / waved part of the rubber will be between the inner and outer part and can be seen from outside. ![]() This rubber part is quite expensive regards Michael | ||||
"oh, for sure, you can do it with a normal streetcar...."
|
||||
| ||||
![]() This one costs by my VolvoTruckdealer here in Germany 90,-€ and in Sweden 1100,- SEK. | ||||
|
viele Grüsse Frank http://www.auf-allen-vieren.de
|
||||
| ||||
|
Pictures say more than a thousand words, now I am almost sure this is indeed the part to be replaced.
Thanks guys for the information and help ![]() greetz.. Joeri | ||||
|
||||
| ||||
|
Oh mein Gott
das is ja ne Operation am offenem Herzen, habe mir die Gummiteile bestellt, weil meine ziemlich porös aussehen. Muss man um die zu wechseln das ganze Radgetriebe inclusive Bremse demontieren.Hilfe........na da bin ich mal gespannt ob/wie ich das wieder zusammenkriege Die übriggebliebenen Teile kann ich ja dann hier im Forum anbieten.... christoph. | ||||
|
||||
| ||||
|
Wenn du was über behältst sag bescheid, ich entsorge es dir kostenlos
![]() | ||||
|
viele Grüsse Frank http://www.auf-allen-vieren.de
|
||||
| ||||
this might help. http://koesters.dk/volvomanuals/section4transmission13.pdf grtz Joeri | ||||
|
||||
| ||||
|
Gibts auch hier im Service Manual Seite 46:46 genau zu sehen, wie man Teil 8 eingauen muß:
![]() Auch gut zu erkennen: Öl aus dem Portal kommt über die Zahnräder 3 nach oben und sickert bis zu einem Level von einigen mm Höhe durch das Lager 4 in Richtung Achsmanschette 8, der Rest läuft wieder runter. Achtung: Im Gegensatz zu den meisten anderen Fahrzeugen mit Frontantrieb ist die Achsmanschette hier feststehen, sie rotiert also nicht mit der Achswelle mit, sondern muß sich nur mit der Lenkung biegen. Mit etwas Glück kann man eine beschädigte Manschette um 45° drehen und hat erstmal Ruhe. Wenn die Manschette aber eingelaufen ist und das Öl an der unteren Kante zum Portal durchsickert, dann braucht man wohl eine elastische neue. Gruß Michael | ||||
"oh, for sure, you can do it with a normal streetcar...."
|
||||
|
||||
| Michaels-Volvo-Offroader-Forum | VOLVO C30x und Verwandte | C303/C304/C306 + TGB-11/13/20/1111 | « vorheriges Thema folgendes Thema » |









Autor







Gespeichert








das is ja ne Operation am offenem Herzen, habe mir die Gummiteile bestellt, weil meine ziemlich porös aussehen. Muss man um die zu wechseln das ganze Radgetriebe inclusive Bremse demontieren.
